Autoglym Polar Blaster Cannon

Your browser's Javascript functionality is turned off. Please turn it on so that you can experience the full capabilities of this site.

Autoglym Polar Blaster Cannon

$0.00

Get $5 credit for every $100 spent†

†T&Cs apply
Learn More

Special Offer

Item No. 599064

Product Info

Polar Blaster is a specialist foam gun, exclusively for use with pressure washers, and designed to work in harmony with the Autoglym Polar Series of products, for the speediest, most high performance and fun way to safely pre-wash, wash and protect.

The Polar Blaster creates lashings of thick, clingy Polar Blast foam, for better pre-wash than rinsing alone, creates an all-over foaming deep wash with Polar Wash, and adds a layer of coating protection with hyper-hydrophobic Polar Seal.

The adjustable spray pattern and swivelling head allows you to easily follow and adjust to contours, ensuring total coverage and maximum effect.

Complete a full exterior car care wash & protect routine in a way that’s quick, fun and water-wise.

Requires some assembly:

Remove all parts from the box and check contents

Attach the clear pickup tube to the brass nozzle on the underside of the Polar Blaster foaming head

The Karcher adaptor is pre-assembled on the spring-loaded collar. If you require the Gerni adaptor, first remove the Karcher adaptor (you may need vice grips; these are assembled and tested under pressure, and can tighten during that process), the attach the Gerni adaptor, a little more that hand tightened

We recommend then attaching the connector to your pressure washer lance, and then attaching this to the nozzle on the foaming head by pulling back the spring-loaded collar, connecting and releasing the collar

Ensure all connections are true before use. You may notice some “slack” in the attachment between the foaming head and lance, though this is normal and will seal under pressure.

Using your Polar Blaster:

Dilute product at the recommended ratios into the Polar Blaster reservoir. These are outlined on the sidewall of the reservoir. Add water first, then product, to prevent too much foaming over. Fill to the desired level

Screw the foaming head onto the reservoir, hand-tighten and attach the Polar Blaster to your pressure washer lance.

Aiming away from what you’re applying too, pull the trigger on your pressure washer, allowing the Polar product to feed through

Although we recommend maximum mix level, you can use the control knob to adjust the amount of solution being picked up by the pressure washer, which will produce less foaming

To adjust the spray pattern wider or narrower, turn the purple nozzle collar to open or close the reeds that are inside

Once you’re happy, start applying!

After use, always flush through the foaming head with clean water, and thoroughly rinse the reservoir.

For further details, click here for and in use demonstration.

Having trouble? Click here for troubleshooting advice.

Included connectors are compatible with the Karcher K-Series, Gerni, Kew, Alto, and Nilfisk Pro Pressure. For other brand pressure washer connectors, please consult with your retailer.

Requires some assembly

Remove all parts from the box and check contents.
Attach the clear pickup tube to the brass nozzle on the underside of the Polar Blaster foaming head.
The Karcher adaptor is pre-assembled on the spring-loaded collar. If you require the Gerni adaptor, first remove the Karcher adaptor (you may need vice grips, as these are assembled and tested under pressure and can tighten during that process), then attach the Gerni adaptor, a little more than hand-tight.
Attach the connector to your pressure washer lance, then attach this to the nozzle on the foaming head by pulling back the spring-loaded collar, connecting, and releasing the collar.
Ensure all connections are secure before use. You may notice some “slack” between the foaming head and lance; this is normal and will seal under pressure.

Using your Polar Blaster

Dilute product at the recommended ratios into the Polar Blaster reservoir, as outlined on the sidewall. Add water first, then product, to prevent excessive foaming. Fill to the desired level.
Screw the foaming head onto the reservoir, hand-tighten, and attach the Polar Blaster to your pressure washer lance.
Aiming away from the surface being treated, pull the trigger on your pressure washer to allow the Polar product to feed through.
Although we recommend the maximum mix level, you can use the control knob to adjust the amount of solution being picked up, which will reduce foaming.
To adjust the spray pattern wider or narrower, turn the purple nozzle collar to open or close the internal reeds.
Once adjusted, begin application.
After use, always flush the foaming head with clean water and thoroughly rinse the reservoir.

Further information and compatibility

For further details, click here for an in-use demonstration.

Having trouble? Click here for troubleshooting advice.

Included connectors are compatible with Karcher K-Series, Gerni, Kew, Alto, and Nilfisk Pro pressure washers. For other brand pressure washer connectors, please consult with your retailer.

Features

Designed to work in harmony with all Autoglym Polar Series products
Speedy and safe way to pre-wash, wash and protect your vehicle
Adjustable spray pattern allows you to evenly coat your cars contours
Adjustable foam thickness lets you choose the concentration of your spray depending on what product you're using
Includes adaptors for use with most Karcher and Gerni pressure washers
1 Year Warranty